SECTION 08385
DOUBLE ACTING IMPACT TRAFFIC DOOR
[POLY-KOR
XHDÔ MODEL]
|
GENERAL
NOTES TO SPECIFIER: |
|
THIS
SPECIFICATION SECTION HAS BEEN PREPARED TO ASSIST DESIGN PROFESSIONALS IN THE
PREPARATION OF PROJECT OR OFFICE MASTER SPECIFICATIONS. IT FOLLOWS GUIDELINES
ESTABLISHED BY THE CONSTRUCTION SPECIFICATIONS INSTITUTE, AND THEREFORE MAY
BE USED WITH MOST MASTER SPECIFICATION SYSTEMS WITH MINOR EDITING. |
|
EDIT CAREFULLY TO SUIT PROJECT REQUIREMENTS.
MODIFY AS NECESSARY AND DELETE ITEMS THAT ARE NOT APPLICABLE. VERIFY THAT
REFERENCED SECTION NUMBERS AND TITLES ARE CORRECT. (NUMBERS AND TITLES
REFERENCED ARE BASED ON MASTERFORMAT,
1995 EDITION). |
|
THIS SECTION ASSUMES THE
PROJECT MANUAL WILL CONTAIN COMPLETE DIVISION 1 DOCUMENTS INCLUDING SECTIONS
01330–SUBMITTAL PROCEDURES, 01620–PRODUCT OPTIONS, 01630–PRODUCT SUBSTITUTION
PROCEDURES, 01660–PRODUCT STORAGE AND HANDLING REQUIREMENTS, 01770–CLOSEOUT
PROCEDURES, AND 01780–CLOSEOUT SUBMITTALS. CLOSE COORDINATION WITH DIVISION 1
SECTIONS IS REQUIRED. IF THE PROJECT MANUAL DOES NOT CONTAIN THESE SECTIONS,
ADDITIONAL INFORMATION SHOULD BE INCLUDED UNDER THE APPROPRIATE ARTICLES. |
|
THIS IS AN OPEN PROPRIETARY
SPECIFICATION ALLOWING USERS THE OPTION OF APPROVING OTHER MANUFACTURERS
WHICH COMPLY WITH THE CRITERIA SPECIFIED HEREIN. |
|
NOTES TO THE SPECIFIER ARE
CONTAINED IN BOXES AND SHOULD BE DELETED FROM FINAL COPY. |
|
OPTIONAL ITEMS REQUIRING
SELECTION BY THE SPECIFIER ARE ENCLOSED WITHIN BRACKETS, E.G.: [35] [40]
[45]. MAKE APPROPRIATE SELECTIONS AND DELETE OTHERS. |
|
ITEMS REQUIRING ADDITIONAL
INFORMATION ARE UNDERLINED BLANK SPACES, E.G.: _____________ . |
|
OPTIONAL PARAGRAPHS ARE
SEPARATED BY “OR” WITHIN A BOX, E.G.: OR |
|
|
PART
1 GENERAL
65535.1 SUMMARY
A. Section Includes: Double acting, self
closing, fully insulated, 1-3/4 inch (44 mm) thick, impact traffic door.
|
INCLUDE APPROPRIATE
SECTION(S) BELOW FOR OPENING FRAMING AND DOOR FRAMES. RECOMMENDED FRAME IS A
6 INCH (152 mm) STEEL CHANNEL WITH A 3/8 INCH (10 mm) WEB (MC6 X 18.0) |
B. Related Sections:
|
INCLUDE APPROPRIATE
LANGUAGE BELOW INCLUDING A REFERENCE TO SECTION 01030–ALTERNATES, IF PRODUCTS
SPECIFIED IN THIS SECTION ARE SUBJECT TO ANY ALTERNATE BID ITEMS, AND ADD
SECTION 01030 TO 1.1 B. OTHERWISE DELETE FOLLOWING PARAGRAPH |
C. Alternates:
65535.2 SUBMITTALS
A. Reference Section 01330–Submittal
Procedures; submit the following items:
1. Product Data.
2. Shop Drawings: Show fabrication details and
anchorage. Include door elevations, head, jamb and meeting stile details
including perimeter air seals.
3. Samples: Full range of manufacturer’s standard
color selections for facing material.
4. Quality Assurance/Control Submittals:
a. Manufacturer’s Installation Instructions.
5. Closeout Submittals:
a. Cleaning and Maintenance instructions.
b. Warranty
65535.3 QUALITY ASSURANCE
A. Qualifications:
1. Manufacturer Qualifications: Minimum five
years experience in producing doors of
the type specified.
65535.4 DELIVERY STORAGE AND HANDLING
A. Reference Section 01660–Product Storage and
Handling Requirements.
B. Verify doors were shipped in upright
position.
1. Note specific doors shipped in other than
upright position on bill of lading and contact manufacturer.
C. Store in upright position and follow
manufacturer’s instructions printed on carton.
65535.5 PROJECT/SITE CONDITIONS
A. Existing Conditions: Frames installed under
other sections shall be level and plumb.
65535.6 WARRANTY
A. One year against defects in materials and
workmanship.
PART
2 PRODUCTS
2.1 MANUFACTURERS
A. Manufacturer: RubbAir Door–Division of Eckel
Industries, Inc.;100 Groton Shirley Rd.; Ayer, MA 01432-1050. Telephone: (800)
966-7822, (978) 772-0480. Fax: (978)
772-7114.
|
INSERT NAME, ADDRESS AND PHONE
NUMBERS OF LOCAL DISTRIBUTOR BELOW. |
1. Distributor:
B. Model: Poly-Kor XHDÔ.
C. Substitutions: Reference Section
01630–Product Substitution Procedures.
2.2 DOOR
COMPONENTS
A. Internal Frame:.
1. Perimeter: 1-1/2 inch (38 mm) square
extruded aluminum tube, 1/8 inch (3 mm) wall thickness with 1-1/4 x 1-1/2 inch
(32x38 mm) rubber honeycomb extrusion at safety nose edge.
2. Stile: 3x1-1/2 inch (76x38 mm) extruded
aluminum tube, full height of mount assembly.
B. Core: 1-1/2 inch (38 mm) thick closed cell
extruded polystyrene foam.
C. Facings: [1/8 inch (3 mm) thick ABS plastic,
5,400 psi (37 MPa) tensile strength, color as selected by architect.] [16 gauge
galvanized steel.] [16 gauge stainless steel, brushed finish.] [16 gauge
aluminum, satin anodized.]
D. Hardware:
1. Cam: “V” cam design; [1-1/2 inch (38 mm)
standard rise] [3/4 inch (19 mm) rise], cast Meehanite, minimum 45,000 psi (310
MPa) compressive strength, ASTM B 633 zinc plated.
a. Swing: [90x90] [90x180] [90x135] degree
swing.
|
SINGLE ACTING (90X0
DEGREE SWING) DOORS ARE AVAILABLE. CONTACT RUBBAIR FOR DETAILS AND MODIFY
SECTION TITLE AND SUMMARY ARTICLE ACCORDINGLY. |
2. Cam Follower: 1-1/8 inch (28 mm) diameter by
5/8 inch (16 mm) wide stud mounted needle bearing roller mounted to cast iron
arm; 2,100 lbf (290 kgm) bearing dynamic capacity.
3. Bottom Bearing: [Combination bottom bearing
and jamb guard, cast Meehanite, minimum 45,000 psi (310 MPa) compressive
strength, ASTM B 633 zinc plated.] [Extruded aluminum bearing.]
4. Hinge Shaft: 1-5/16 inch (33 mm) diameter
full height steel tube, 62,000 psi (430 MPa)
tensile strength.
5. Mount Plate: Full height of door panel by
4-1/2 inch (115 mm) wide, 12 gauge anodized aluminum.
E. Safety Nosing: Full height, 2-ply,
reinforced rotocured rubber, 2,200 psi (15 MPa) tensile strength with 1/16 inch
(2 mm) vinyl loop seal (loop seal on one leaf at pairs of doors).
F. Seals: Less than 5 cfm (.002 m³/s) air
infiltration per linear foot of seal per ASTM E 283.
1. Jamb and Header: Polymer impregnated woven
nylon fabric in hollow-loop configuration. Jamb seal: Factory installed; fixed.
Header seal: Field installed; adjustable.
2. Sill: 1/16 inch (2 mm) thick neoprene
rubber, factory installed; fixed.
3. Hardware Cutouts: 1/16 inch (2 mm) thick
neoprene rubber, factory installed; fixed.
G. Bumpers: 42 inch (1.06 m) high, [1/4 (6 mm) inch
thick molded polyethylene.] [3/8 inch (10 mm) thick crackcord rubber.]
|
24 INCH (610 mm) HIGH BY FULL WIDTH VISION
PANEL IS STANDARD; OPTIONS INCLUDE 7-1/2 X 10-1/2 (190X265 mm), 11-1/2 X
15-1/2 (290X380 mm), 16X18 (405X455 mm) AND 24X24 (610X610 mm). SHOW PANEL
SIZE AND LOCATION ON DRAWINGS. |
H. Vision Panel: 1/8 inch (3 mm) thick
polycarbonate, double glazed in aluminum subframe mechanically attached; panels
flush with both door faces.
I. Hold Open Pin: 1/4 inch (6 mm) diameter
steel pin with wire ring and 8 inch (205 mm) chain for attachment to jamb.
J. Cam Shields: [1/16 inch (2 mm) black rubber
flap] [ABS plastic, color to match door facing], field installed.
|
FOLLOWING ACCESSORIES ARE
OPTIONAL. SELECT AS DESIRED AND DELETE OTHERS. |
2.3 ACCESSORIES
|
PAD TYPE IMPACT
PANELS PROVIDE BEST SEAL; WRAP AROUND TYPE COVERS SAFETY NOSING, BUT
COMPRESSES LOOP SEAL AND REDUCES SEAL EFFICIENCY. |
A. Impact Panels: [12 inch (300 mm)] [24 inch
(600 mm)] [36 inch (900 mm)] [48 inch (1.22 m)] high, 1/8 inch (3 mm) thick
vinyl, [pad type] [wrap around type], color as selected by Architect.
B. Flex Shield: [12 inch (300 mm)] [24 inch
(600 mm)] [36 inch (900 mm)] [48 inch (1.22 m)] high, 3/8 inch (10 mm) thick
crackcord rubber (pad style only).
C. Wear Strips: 1/4 inch (6 mm) thick high
density polyethelene, ____ inches (___
mm) high by full width of panel; black.
|
FOLLOWING JAMB
GUARD IS FOR USE WITH EXTRUDED ALUMINUM BOTTOM BEARING. DELETE IF STANDARD
COMBINATION BOTTOM BEARING AND JAMB GUARD WAS SELECTED IN 2.2 D. 3. |
D. Jamb Guards: 1/4 inch (6 mm) bent steel
plate, 3x6x8-3/4 inches (75x150x220 mm).
E. Pressure and Wind Load Accessories:
1. Adjustable Spring Compensator.
2. Compression Spring.
3. Deep seat cam.
|
FOLLOWING LOCKING DEVICE IS
STANDARD FOR PADLOCK (NOT SUPPLIED); CONTACT RUBBAIR FOR OTHER OPTIONS. |
F. Locking Device: 1 inch (25 mm) i.d. cast
aluminum bushing (2 per leaf) with two 3/16 inch (5 mm) by 30 inch (760 mm) long
galvanized proof coil chains.
G. Transom Flap: 2 ply vinyl, color as selected
by Architect.
|
TRACK PORTS AND MEAT RAIL
CUTOUTS, IF REQUIRED, SHOULD BE SHOWN ON DRAWINGS. |
2.4 FABRICATION
A. Shop Assembly: Fabricate door components
into 1-3/4 inch (44 mm) thick unitized welded aluminum frame assembly with
facings through riveted and adhesive bonded to core and frame. Adhesive peel
strength shall be 60 piw minimum, standard 2 inches per minute at 25 degrees
C., Scott tester. Rigidly connect mount plate, stile and hinge shaft and secure
hardware assembly to door with through-rivets at tubing and aluminum or
stainless steel screws to stile. Align cam hardware and prepin.
2.5 SOURCE
QUALITY CONTROL
A. Fabrication Tolerances: Width and height of
each leaf: + 0, -1/8 inch (3 mm).
PART
3 EXECUTION
3.1 EXAMINATION
A. Examine opening in which door will be
installed.
B. Coordinate with responsible entity to
perform corrective work on unsatisfactory conditions.
C. Commencement of work by installer is
acceptance of opening conditions.
3.2 INSTALLATION
A. Follow manufacturer’s instructions.
B. Install door with necessary anchors,
hardware and accessories.
1. Drill bottom bearing for hold open pin.
3.3 ADJUSTING
A. Follow manufacturer’s instructions as
required to:
1. Clean and lubricate operating parts.
2. Adjust to open and close smoothly and
freely without binding.
3. Check seals for proper fit.
3.4 CLEANING
A. Clean surfaces soiled by work as recommended
by manufacturer.
B. Remove surplus materials and debris from the
site.
END OF SECTION[1]